PDA

View Full Version : gsxr600 bypass sensors



hodakaracer
12-10-2008, 08:02 AM
Ive seen different answers concerning bypassing clutch,sidestand and to sensors. clutch; jump two wires. sidestand; use 100 or 100k resistor? TO sensor; three wires. Use one or two resistors? 100 or 100k resistor? Please help. Thanks Doyle

plkracer
12-10-2008, 11:18 AM
I know the TO is a 65K resistor, so something close. Not sur which wires to put it between though. Also, the side stand doesn't need a resistor, just connect it to ground.

Bugpac
12-10-2008, 01:16 PM
fill the to sensor with silicone so it cant move...

Shmeefer
12-10-2008, 01:50 PM
Would you have to bypass the TO sensor? The TO sensor works on the roll axis and won't kick in until bike is pretty much on it's side (they usually do not go off on the track) so it would only go off if you rolled your buggy (assuming the engine is oriented the same as in the bike), in which case it might be good to have it on there, IMO. If I'm wrong, I'd love to learn why the more experienced have done it... you can't learn less.

Bugpac
12-10-2008, 01:53 PM
Would you have to bypass the TO sensor? The TO sensor works on the roll axis and won't kick in until bike is pretty much on it's side (they usually do not go off on the track) so it would only go off if you rolled your buggy (assuming the engine is oriented the same as in the bike), in which case it might be good to have it on there, IMO. If I'm wrong, I'd love to learn why the more experienced have done it... you can't learn less.


Mine was going off about every bump, lol... I took it apart and filled it with silicone...

Shmeefer
12-10-2008, 02:10 PM
Interesting... I'll keep that in mind. I have heard of filling with silicone, some racers do this to save the hassle.

ProtoDie
12-10-2008, 02:24 PM
On the 2004 gsxr600 (and maybe newer), you can take the TO sensor out and put a 100ohm resitor between the red & black wires in the plug.
I just pushed the ends right into the plug and then taped it up.

hodakaracer
12-10-2008, 05:00 PM
plkracer says 65k and protodie says 100 ohm. thanks for the response but I'm still confused

plkracer
12-10-2008, 05:31 PM
I'm going from my service manual, 00-03.

plkracer
12-10-2008, 05:32 PM
60-64 kilo ohm resistor between the black and the black with white tracer (ground).

hodakaracer
12-10-2008, 05:59 PM
Mine has red,black and black with brown tracer. I've got 100 and 100k resistors so I think I will try protodie's advice and try both and see which one works. Thanks

ProtoDie
12-10-2008, 06:02 PM
The 2003 & 2004 TO sensors are different. Actually there are quite a few differences in the wiring from the model change year 03 to 04.

There may be a range of ohms res sizes that work,,,not sure

100ohm res is what I did, and what worked on my 2004 and has been running strong with no problems.


What year motor do you have?

bigtuna
12-10-2008, 08:51 PM
Mine is a 2005 and I used a 63K ohm solder to wires and shrink wrapped for the TO sensor. Jumped the sidestand out and shrinkwrapped, put in a brake light switch on the clutch line and put the clutch switch wire on it so the wife and kids can't start it in gear.

hodakaracer
12-11-2008, 06:15 AM
did you put a resistor in when you jumped the side stand switch? on the to, which wires did you jump?

Maxis
12-12-2008, 07:01 PM
We were running a 2005 GSXR 600 and I took it 6' high and 40' long never set off. Played sideways on hills for hours and never set off. I too though good idea to keep in case of roll over. Wire kickstand together and resistor for key switch.

magnum4598
01-08-2009, 04:55 PM
i just want to know what a to sencor is i have a 1998 gsxr engine on my buggy and i have never hurd of it lol

onlyguy
01-08-2009, 05:15 PM
tip over

MXman
01-09-2009, 04:11 PM
One the clutch on just cut the wire that goes into the CPU and connect the 2 wires so the starter relay works. If you just put a jumper across the 2 wires and dont cut the CPU wire it limits the RPM.

plkracer
01-12-2009, 02:41 AM
I put a switch in mine. I found myself forgetting the clutch every once in a while. Not good for the starter.