Activity Stream
-
Older Activity
-
Yesterday, 10:16 PMif you are worried about the integrity of the build and planning to sell it, you should do full disclosure to the next buyer, don't be like the guy...3 replies | 78 view(s)
-
Yesterday, 03:12 AMOnly 2wd UTVs I know of are the Odysseys, John Deere Gators, and some flavors of the Kawasaki Mules. I believe the latter uses more or less a...39 replies | 6671 view(s) -
02-28-2021, 03:31 PMdarwinpayne2000 replied to a thread Re-engine Buggy with a (modified) Predator 670 in Projects in ProgressA quick update on the minibike. I have the exhaust, the throttle and the seat in place. The gas tank still needs to be bolted down, then it's...165 replies | 21161 view(s)
-
02-28-2021, 03:15 PMI've been using a Lincoln Weldpak 100 120v welder from the get-go. I'm using the flux-core wire, not gas, so I can weld up to 1/4". You don't get...2 replies | 86 view(s)
-
02-28-2021, 02:18 PMConcept looks sound. lol on the monitor pic - I discovered the same a few days ago.120 replies | 15590 view(s)
-
02-28-2021, 02:16 PMHmmmmm.... I don’t know quads well enough to even begin to give advise on that (I run away from those wretched machines!) and a 2wd UTV, uh... What...39 replies | 6671 view(s)
-
02-28-2021, 02:08 PMIf you’re having to put all that effort into just getting it ready to be useable, may as well start out with new tubing and build from the ground up....3 replies | 78 view(s)
-
02-28-2021, 09:55 AMSell it and start again. Fix it and run it as is. Fix and improve on it in stages. What do you want. How much do you want to spend.3 replies | 78 view(s)
-
02-28-2021, 03:53 AMMy personal opinion on this (I'm not a materials expert) but looks more like surface rust to me. I'd guess it's pretty localize to where any water...27 replies | 1209 view(s)
-
02-28-2021, 02:35 AMHi MBN community, over the summer of 2020 I acquired a badlands buggy st3 frame. Recently i just started to get on to working on it and the more I...27 replies | 1209 view(s)
-
02-28-2021, 02:34 AMHi MBN community, over the summer of 2020 I acquired a badlands buggy st3 frame. Recently i just started to get on to working on it and the more I...3 replies | 78 view(s)
-
02-28-2021, 02:00 AMI'm probably the last person to give welding advice, but yeah, if you see welds that look kind of sketchy, grind them out and reweld them. If a weld...2 replies | 67 view(s)
-
02-28-2021, 01:53 AMAny suggestions on what quad or UTV to get hubs from that's two wheel drive? Would it also be better to go with an OEM style or is there a better...39 replies | 6671 view(s)
-
02-27-2021, 07:55 PMAnother Question: What do you do if the rust is inside of your tubing on your sand rail? My project St3 has holes in it for the flooring. When you...2 replies | 67 view(s)
-
02-27-2021, 07:53 PMWhat do you do if the rust is inside of your tubing on your sand rail? My project St3 has holes in it for the flooring. When you look through the...27 replies | 1209 view(s)
-
02-27-2021, 12:54 AMWhat kind of 120V welder? For the wall thickness buggy cages a made out of 120V welders usually have plenty of power.2 replies | 86 view(s)
-
02-26-2021, 10:38 PMNot much physical progress as I'm cleaning up my shop to make room for the lathe which is coming next week. I have a little more progress into the...120 replies | 15590 view(s)
-
02-26-2021, 01:54 PMIf you are going to stick weld it then your best option would be 3/32 7018 rod. Make sure the weld area is clean, you wont need a lot of amperage...27 replies | 1209 view(s)
-
02-26-2021, 01:34 PMAbsolutely!39 replies | 6671 view(s)
-
02-26-2021, 12:48 PMI seen him in the pits after the race to apologize, he had my tire mark going across the back of his chest protector..lol909 replies | 85702 view(s)
-
02-26-2021, 01:56 AMI have two welders. a light duty 120v MiG welder, and a 120v/240v Hobart DC inverter. Could I use the stick welder running on 240v to weld some...27 replies | 1209 view(s)
-
02-26-2021, 01:55 AMI have two welders. a light duty 120v MiG welder, and a 120v/240v Hobart DC inverter. Could I use the stick welder running on 240v to weld some...2 replies | 86 view(s)
-
02-26-2021, 01:47 AMI bought a badlands buggy st3 rolling chassis buggy last year. Most of the welds are very poor and don't look like they have good fusion. could I...2 replies | 67 view(s)
-
02-26-2021, 12:34 AMWould it be worth switching the front end design of using trailer stub axles and hubs for ATV/UTV hubs that have disc or drum brakes to have front...39 replies | 6671 view(s)
-
02-25-2021, 10:08 PMYou beast!909 replies | 85702 view(s)
-
02-25-2021, 12:14 PMI ran straight over a guy once while racing, looking back I think I could’ve stopped LOL909 replies | 85702 view(s)
-
02-24-2021, 10:42 AMWere there 2 EMT takedowns? I was thinking it was Hunter Lawrence that took the guy out in the corner. Maybe not though. The 450's have been...909 replies | 85702 view(s)
-
02-23-2021, 11:02 PMWhen I saw the replay all I could think was “Ouch! Peg to the leg take down!” Right up there with trailer hitch to the shin to thigh depending on...909 replies | 85702 view(s)
-
02-23-2021, 09:57 PMYa his line was clear then the medic kind of closed the distance. A block pass if you will..lol909 replies | 85702 view(s)
-
02-23-2021, 12:29 PMA lot of controversy about that. If you watched, they put tough blocks out to funnel the racers up around the down rider. EMT ran across the race...909 replies | 85702 view(s)
