Activity Stream
-
Older Activity
-
Today, 09:24 PMOne of the main reasons some people are opposed to completely switching engines is that would mean we would be at square one as far as any engine...2 replies | 39 view(s)
-
Today, 04:22 PMHonestly switching to a common street bike engine, or even dirt bike engine may be the way to go. One team I am quite familiar with runs a cycle...2 replies | 39 view(s)
-
Today, 03:34 PMHey all this is a little different than the usual off road stuff we're used to, but I was just having a discussion with other members of my college's...2 replies | 39 view(s)
-
12-08-2019, 03:22 AMAfter quite a bit of searching, it turns out that the 5/8 master cylinder for these is the TM1 Tandem Master cylinder. Needs two reservoirs and...1 replies | 447 view(s)
-
12-06-2019, 11:12 PMHoly cow that is a super low price, even at $100 each it's a bargain!!3 replies | 299 view(s)
-
12-06-2019, 08:02 PMHoly crap - all four for 100??? SOMEONE JUMP ON THIS!3 replies | 299 view(s)
-
12-06-2019, 03:06 PMYes, the Dimensions are listed on the website, It's 1.25 x .120 Tubing, uses a 3/8" Bolt, and mounts at 2" Wide I believe. You would weld the tube...37 replies | 2608 view(s)
-
12-06-2019, 12:15 PMI'm interested, sent you a PM3 replies | 299 view(s)
-
12-05-2019, 08:50 PMI have four 1 1/4" shaft Fox air shocks that I am no longer using, went to CO's. (2) 12" with no shim stacks in them. (2) 10" valved 70/50. All...3 replies | 299 view(s)
-
12-05-2019, 08:18 PMBought these this summer and had them on for one ride. 1" thick 6061 Billet Aluminum, 4 x 156 bolt pattern with 3/8-24 lugs. 5 3/16" ID - 7 1/2" OD ...0 replies | 171 view(s)
-
12-05-2019, 08:05 PMThat is very much appreciated. For my post #67 above, I was trying to see if that (white tubes) was the proper approach to connecting a belly...68 replies | 4887 view(s)
-
12-04-2019, 08:48 PMGlad its fixed too...also interested in your turbo info....thanks7 replies | 1006 view(s)
-
12-04-2019, 03:27 PMGlad it got fixed! Did you do a home made turbo set up for it? If so, please post pictures and component info! Thanks, Justin7 replies | 1006 view(s)
-
12-04-2019, 12:54 PMI think you are going in the right direction for sure. Some areas seem like they are overly complicated and may be hard to build. Below are some...68 replies | 4887 view(s)
-
12-04-2019, 12:29 AMI played that game on my current buggy. I went with a ‘bud light’ blue with red accents. Called it my my little buddy build. Unfortunately the paint...15 replies | 2273 view(s)
-
12-03-2019, 11:00 PMStarting to look like something! I've still got a ways to go on the cage but at least my suspension is all welded. What are some good looking...15 replies | 2273 view(s)
-
12-03-2019, 12:22 AMNot with my setup. I host the pix on yellowdogracing and link to them.1987 replies | 322037 view(s)
-
12-02-2019, 12:22 AMOne thing you might be able to do.....some forum software has an available feature under “thread tools” that allows you to “view attachments” as a...1987 replies | 322037 view(s)
-
12-02-2019, 12:16 AMHey! Haven’t seen you here in a while. Thanks for the compliment. Unfortunately no, I don’t other than in this thread.1987 replies | 322037 view(s)
-
12-01-2019, 06:16 PMWhile I gave up on my MiniBuggy project forever ago and sold it for parts.... YOURS TURNED OUT TO BE THE COOLEST THING EVER. Do you have a photo...1987 replies | 322037 view(s)
-
11-30-2019, 01:17 AMI used that same size as the 4wd link (1.25" O.D.) for my front A-arms. I used larger bushings like these from Barnes 4wd for my rear...37 replies | 2608 view(s)
-
11-29-2019, 11:07 PMSo what size did you end up using? You know of Anywhere to get dimensions?37 replies | 2608 view(s)
-
11-29-2019, 02:27 AMLooking at the Willwood website at the SC1 brake calipers, thinking about using 3 (1 rear on the spool, 2 up front), but I'm having a hard time...1 replies | 447 view(s)
-
11-29-2019, 01:28 AMSpent some time adding in some diagonal braces to the chassis to help stiffen it up. Also got an engine hoist to finally move the motor into place...21 replies | 2299 view(s)
-
11-29-2019, 01:21 AMYep, tack it in so you get it in the right place, remove the inner sleeve, poly bushings and weld the outer sleeve in place. Sent from my SM-G900V...37 replies | 2608 view(s)
-
11-29-2019, 12:16 AMHow do these things work exactly? can you remove the rubber part of the thing and weld it? Or do you buy a pipe with the ID the same as it's OD and...37 replies | 2608 view(s)
-
11-27-2019, 02:05 AMYour welcome odypilots... fns....i'll try and not to be lazy with it...thanks for the info.....is your busa a gen 2 ?? is it turbo??10 replies | 1539 view(s)
-
11-27-2019, 01:26 AM151 replies | 46127 view(s)
-
11-27-2019, 01:22 AMYeah , when I use the little picture icon it makes the pic small like yours.12 replies | 1053 view(s)
-
11-27-2019, 01:15 AMok, someone please take a look at what I have done. I wasn't sure how to attach or structurally connect the pan rails to the rest of the cage. So, I...68 replies | 4887 view(s)