Activity Stream
-
Older Activity
-
Today, 10:42 AMWere there 2 EMT takedowns? I was thinking it was Hunter Lawrence that took the guy out in the corner. Maybe not though. The 450's have been...906 replies | 84581 view(s) -
Yesterday, 11:02 PMWhen I saw the replay all I could think was “Ouch! Peg to the leg take down!” Right up there with trailer hitch to the shin to thigh depending on...906 replies | 84581 view(s)
-
Yesterday, 09:57 PMYa his line was clear then the medic kind of closed the distance. A block pass if you will..lol906 replies | 84581 view(s)
-
Yesterday, 12:29 PMA lot of controversy about that. If you watched, they put tough blocks out to funnel the racers up around the down rider. EMT ran across the race...906 replies | 84581 view(s)
-
Yesterday, 11:44 AMDamn! Jmart was off to good start too!906 replies | 84581 view(s)
-
Yesterday, 02:01 AMLooks like Jeremy Martin has a separated shoulder, and Alex has a concussion. AC has a broken collar bone and a sore back.. Enticknap and Sean...906 replies | 84581 view(s)
-
Yesterday, 01:50 AMDid they ever say who it was that hit the medic? I could have paused it and looked, but I wasn't thinking of it at the time. EDIT Just googled it,...906 replies | 84581 view(s)
-
02-22-2021, 06:12 PMYeah the medic should have never been hit. Whats up with Toemac? Even struggling in the heat race.906 replies | 84581 view(s)
-
02-22-2021, 04:15 PMI'll paraphrase a joke I read recently. A farmer back in the 1800's was approached by a government official and told that a revised survey put his...141 replies | 17530 view(s)
-
02-22-2021, 03:52 PMYou missed the moose-can ramble..lol Hope AC and the Martin brothers are ok. The first start to that 250 race was a nightmare, even one of the...906 replies | 84581 view(s)
-
02-22-2021, 12:31 PMQuick little update... temps have been in the negatives for almost 2 weeks straight! Shop isn't heated so even with the coolant in the reservoir,...141 replies | 17530 view(s)
-
02-21-2021, 06:09 PMNobody has posted anything on this thread for awhile, so I'll share a link to a Youtube video and channel (What's Going on in Doug's Shed) that's...479 replies | 230924 view(s)
-
02-21-2021, 12:13 PMI took The Wizard up there the back way a couple of months ago on bikes. no snow then. Did get into the stuff a few years back - started there...2375 replies | 411339 view(s)
-
02-21-2021, 06:20 AMCrown King.....that would be better......sure it snows up there, but go across the bridge and the snows gone.2375 replies | 411339 view(s)
-
02-21-2021, 02:11 AM250 Racing was sort of bland. Not bad, not good. Generally clean. 450 main may have been one of the best races so far. Marvin’s podium speech: ...906 replies | 84581 view(s)
-
02-20-2021, 03:34 PM330* makes me cringe LOL. Was looking at Mobil 1's ratings and they claim up to 500*. I'd really prefer not to test that.2375 replies | 411339 view(s)
-
02-20-2021, 01:11 PMKuma - was told that 330 is upper range. My running oil temps were 240ish so there’s another 80+ degrees of headroom. The oil temp graph is quite...2375 replies | 411339 view(s)
-
02-20-2021, 02:46 AMI have been following along... great news!! As you can imagine I have been encompassed with negative zero temps and trying to get the house...2375 replies | 411339 view(s)
-
02-19-2021, 08:50 PMassuming you have an oil cooler I would think 320 is getting a bit high, once you are driving it more and feel it is where it wants to be then you...2375 replies | 411339 view(s)
-
02-19-2021, 08:14 PMAlso talked with my buddy Don and discussed oil temps. Said that 235F is absolutely fine. Told me to set the alarm at 335F. His old...2375 replies | 411339 view(s)
-
02-19-2021, 08:05 PMUpdated my previous post with a few pix Okay, maybe not as bad as I thought. Made some washers and stuck em' in. They're not as flexy flyer as...2375 replies | 411339 view(s)
-
02-19-2021, 03:09 PMThe NZ 10 cars look sweet! Nice job dude!4 replies | 109 view(s)
-
02-19-2021, 02:14 PMJust looked through your work. Very nice!4 replies | 109 view(s)
-
02-18-2021, 09:45 PMNo room left in the garage, so buying a lathe would force me to pull the trigger on building a shop. I essence, an el-cheapo lathe would still cost...3 replies | 141 view(s)
-
02-18-2021, 05:45 PMvery nice presentation, [smilie=rockout3.gi:4 replies | 109 view(s)
-
02-18-2021, 02:50 PMSounds like a quality idea. Are you on the FaceBook group of MBN? That would be a good place to throw that out also.4 replies | 109 view(s)
-
02-18-2021, 11:06 AMHi all, I have been bored during the lockdown, and have been revisiting my old obsession with minibuggies. I thought I would start a collection of...4 replies | 109 view(s)
-
02-18-2021, 02:22 AMI believe it is. I didn’t realize how much of a pain changing belts would be. Sent from my iPhone using Tapatalk3 replies | 141 view(s)
-
02-18-2021, 01:40 AMWell, I pulled the trigger on a lathe today. I've been wanting one for quite a while and I'm at a point in the build where having one will speed up...118 replies | 15279 view(s)
-
02-17-2021, 11:51 PMHad a few moments in the shop - did a quick camber adjustment on my old XP900, as my friend who bought them from us is selling it on Saturday. Had...2375 replies | 411339 view(s)
