Activity Stream
-
Older Activity
-
229 replies | 105172 view(s)
-
Today, 10:24 PMSecond step - titling & registration. (Expanded recap) Itty bitty woman (of whom had an itty bitty mask covered voice “What?” “Excuse me?”) looks...2378 replies | 413035 view(s)
-
Today, 05:54 PMNice!!!2378 replies | 413035 view(s)
-
Today, 04:31 PMOkay, I think things are in order. First thing to address was the water temp sensor. Since I had to pull the intake system off (it's really not...2378 replies | 413035 view(s)
-
Yesterday, 11:45 PMWe are always happy to help. :)5 replies | 123 view(s)
-
Yesterday, 10:29 PMI've decided I'm going to just use the frame as a learning platform and just build it. Luckily I am buying a Hobart 140 MiG which should make this...28 replies | 1273 view(s)
-
Yesterday, 10:22 PMOk, thanks for the input! JMperformance4 replies | 109 view(s)
-
Yesterday, 10:19 PMI totally agree with you. Nobody likes a liar. After some consideration and thinking, I have decided I will stick with the frame and just use it...5 replies | 123 view(s)
-
Yesterday, 07:59 PMYou have come to the right place. Heaps of build info throughout the site and a heap of big kids who love mini buggys. Have a dig through the...1 replies | 38 view(s)
-
Yesterday, 05:58 PMI downsized from a full tube chassis rock crawler to a Can Am outlander 400HO ATV. I like the simplicity of laod and go, and there are more areas to...1 replies | 38 view(s) -
Yesterday, 07:05 AMThat rust is nothing to stress about. Very light surface rust only.4 replies | 109 view(s)
-
03-02-2021, 10:16 PMif you are worried about the integrity of the build and planning to sell it, you should do full disclosure to the next buyer, don't be like the guy...5 replies | 123 view(s)
-
03-02-2021, 03:12 AMOnly 2wd UTVs I know of are the Odysseys, John Deere Gators, and some flavors of the Kawasaki Mules. I believe the latter uses more or less a...39 replies | 6767 view(s)
-
02-28-2021, 03:31 PMdarwinpayne2000 replied to a thread Re-engine Buggy with a (modified) Predator 670 in Projects in ProgressA quick update on the minibike. I have the exhaust, the throttle and the seat in place. The gas tank still needs to be bolted down, then it's...165 replies | 21302 view(s)
-
02-28-2021, 03:15 PMI've been using a Lincoln Weldpak 100 120v welder from the get-go. I'm using the flux-core wire, not gas, so I can weld up to 1/4". You don't get...2 replies | 107 view(s)
-
02-28-2021, 02:18 PMConcept looks sound. lol on the monitor pic - I discovered the same a few days ago.120 replies | 15671 view(s)
-
02-28-2021, 02:16 PMHmmmmm.... I don’t know quads well enough to even begin to give advise on that (I run away from those wretched machines!) and a 2wd UTV, uh... What...39 replies | 6767 view(s)
-
02-28-2021, 02:08 PMIf you’re having to put all that effort into just getting it ready to be useable, may as well start out with new tubing and build from the ground up....5 replies | 123 view(s)
-
02-28-2021, 09:55 AMSell it and start again. Fix it and run it as is. Fix and improve on it in stages. What do you want. How much do you want to spend.5 replies | 123 view(s)
-
02-28-2021, 03:53 AMMy personal opinion on this (I'm not a materials expert) but looks more like surface rust to me. I'd guess it's pretty localize to where any water...28 replies | 1273 view(s)
-
02-28-2021, 02:35 AMHi MBN community, over the summer of 2020 I acquired a badlands buggy st3 frame. Recently i just started to get on to working on it and the more I...28 replies | 1273 view(s)
-
02-28-2021, 02:34 AMHi MBN community, over the summer of 2020 I acquired a badlands buggy st3 frame. Recently i just started to get on to working on it and the more I...5 replies | 123 view(s)
-
02-28-2021, 02:00 AMI'm probably the last person to give welding advice, but yeah, if you see welds that look kind of sketchy, grind them out and reweld them. If a weld...4 replies | 109 view(s)
-
02-28-2021, 01:53 AMAny suggestions on what quad or UTV to get hubs from that's two wheel drive? Would it also be better to go with an OEM style or is there a better...39 replies | 6767 view(s)
-
02-27-2021, 07:55 PMAnother Question: What do you do if the rust is inside of your tubing on your sand rail? My project St3 has holes in it for the flooring. When you...4 replies | 109 view(s)
-
02-27-2021, 07:53 PMWhat do you do if the rust is inside of your tubing on your sand rail? My project St3 has holes in it for the flooring. When you look through the...28 replies | 1273 view(s)
-
02-27-2021, 12:54 AMWhat kind of 120V welder? For the wall thickness buggy cages a made out of 120V welders usually have plenty of power.2 replies | 107 view(s)
-
02-26-2021, 10:38 PMNot much physical progress as I'm cleaning up my shop to make room for the lathe which is coming next week. I have a little more progress into the...120 replies | 15671 view(s)
-
02-26-2021, 01:54 PMIf you are going to stick weld it then your best option would be 3/32 7018 rod. Make sure the weld area is clean, you wont need a lot of amperage...28 replies | 1273 view(s)
-
02-26-2021, 01:34 PMAbsolutely!39 replies | 6767 view(s)
