Activity Stream
-
Older Activity
-
Today, 04:23 AMEpic! [smilie=thumbs_up.g:[smilie=thumbs_up.g:[smilie=thumbs_up.g:[smilie=ext_hooray.:[smilie=ext_beer2.g:[smilie=non_banana1:[smilie=rockout3.gi:255 replies | 23339 view(s)
-
Today, 04:18 AMlol2605 replies | 610140 view(s)
-
Yesterday, 10:43 PMPut carb back together and response seems the same. Turned slow speed screws out another 1/8 each for kicks. Painted the header. Test drive revealed...255 replies | 23339 view(s) -
Yesterday, 07:03 PMRear suspension coming together.... Fitted with a 52T sprocket. Skid shown here will clear up to 60T. Axle shafts are 18.75" 28-spline. ...23 replies | 1078 view(s)
-
Yesterday, 06:41 PMThanks! Engine going in....23 replies | 1078 view(s)
-
Yesterday, 02:48 PMThat’s how I understood the jetting also. Good to know on the fuel pump and that the cutout switch is easily rectifiable. I may add another throttle...255 replies | 23339 view(s)
-
Yesterday, 02:37 PMThe different-sized jets were due to the exhaust pipe. One cylinder had a much longer distance through the muffler to exhaust, so the intake/exhaust...255 replies | 23339 view(s)
-
Yesterday, 01:58 PMHave to throw in a little theoretical scientific-ness sometimes right? :p Hoping to get a test run in later today. Maybe I should do a timed 60’...255 replies | 23339 view(s)
-
Yesterday, 10:34 AMHow are those wind chimes going K ???2605 replies | 610140 view(s)
-
Yesterday, 01:00 AMYour using Pythagoras now!255 replies | 23339 view(s)
-
Yesterday, 12:18 AMDrilled the stock main jets from .0395” (.040” for ease of numbers) to .042”; just over a 7 percent increase from stock. The 108 main jet measured...255 replies | 23339 view(s)
-
08-10-2022, 06:47 PMThanks Darwin! I hammered on it yesterday, and it seems cooler now with the belt being tightened. The next belt I get will probably be around half an...255 replies | 23339 view(s)
-
08-10-2022, 01:04 PMThe Dayco part number on your belt, HP3004, is a 1-3/16 belt. Since it's a little worn, it probably measures as a 1-1/8 belt. The center-to-center...255 replies | 23339 view(s)
-
08-09-2022, 07:40 PMDone (minus paint). Sounds OK with the baffles on, and very nice with them off.255 replies | 23339 view(s)
-
08-09-2022, 03:44 PMI don't know if Neil at ATV Racing in Phoenix can help but he may have info. (623) 516-86402 replies | 212 view(s)
-
08-09-2022, 01:10 AMHeader so far. I formed the collector by hand, literally as I don’t have an anvil here at the moment.255 replies | 23339 view(s)
-
08-09-2022, 01:08 AM39mph is fast enough to get around. Few tweaks and there is more to be had to. Well done! :)255 replies | 23339 view(s)
-
08-08-2022, 09:33 PMWe’re up to 39mph and a much better takeoff. Won’t burn tires on pavement, but it should leave a mini-roost on dirt. Good enough for now until...255 replies | 23339 view(s)
-
08-08-2022, 03:40 PMI do need new front tires as these I picked up for $20 used, and they were a pain to put on. Im probably just going to cut the old arms off and...255 replies | 23339 view(s)
-
08-08-2022, 12:50 PMMan, that looks really nice. It will be a shame to get it all dirty when it's finished. :D23 replies | 1078 view(s)
-
08-08-2022, 12:48 PMThe Ridge Runner uses parts from a Polaris Sportsman ATV, if I remember correctly. I would bet that the sprockets from a Polaris would match yours.2 replies | 212 view(s)
-
08-08-2022, 12:45 PMWhen you get your Ackerman working right, let me know how you did it so I can fix mine. :) The way it's supposed to work is that you draw a line...255 replies | 23339 view(s)
-
08-08-2022, 06:13 AMI'd say it's more your tires. Great first tests. Few changes needed but it drove!255 replies | 23339 view(s)
-
08-08-2022, 12:57 AMFirst 2 test drives went well. Since then, I’ve tightened the belt considerably but haven’t run it yet. I think it was way too loose since it lacks...255 replies | 23339 view(s)
-
08-07-2022, 11:54 PM[smilie=ext_hooray.:[smilie=ext_beer2.g:[smilie=rockout3.gi:[smilie=thumbs_up.g:234 replies | 48436 view(s)
-
08-07-2022, 08:54 PMWent to the auto parts store after church and picked up a bottle of brake fluid. My wife helped me bleed the brakes and she even cleaned up my shop a...255 replies | 23339 view(s)
-
08-07-2022, 08:35 PMYep, its an old screwdriver I'm using for the shift lever. I liked it and made things simple not having to build something fancy. I also wanted a...234 replies | 48436 view(s)
-
08-07-2022, 10:19 AMSo close. Talk about excitement plus! [smilie=ecstatic.gi:[smilie=ecstatic.gi:[smilie=ecstatic.gi:255 replies | 23339 view(s)
-
08-07-2022, 02:40 AMPut a wheel on and did a short burst-run up to speed on a jack stand. I’m not sure what rpm the motor attained (have to get a mini tach), and even...255 replies | 23339 view(s)
-
08-06-2022, 02:36 PMHi - I am looking for some ridge runner parts or a parts car. Primarily I need the gear that goes between the differential and the transmission...2 replies | 212 view(s)
