Activity Stream
-
Older Activity
-
Today, 12:57 PMWho let the duck in here? They say Kfab could have started the big bang with a sneeze and his feet have 6 toes..... But all we know is he's...2608 replies | 611534 view(s)
-
Yesterday, 05:32 PMWell the 250’s were action packed, gonna watch the 450’s later.371 replies | 87520 view(s) -
08-13-2022, 11:11 AMSo, has your mechanical madness gone toward- Hmmm. I could make a turbine for the trickle charging of my toys???2608 replies | 611534 view(s)
-
08-12-2022, 05:39 PMFunny you ask. Was outside playing with the blade balance about 3-4 minutes ago on one of the fans. It’s spinning better now. I have another set...2608 replies | 611534 view(s)
-
08-12-2022, 03:47 PMGreat info, thanks! I’m really thankful you did the R and D for all of this.259 replies | 23512 view(s)
-
08-12-2022, 02:56 PMThe low oil sensor is a good idea for the original purpose, where the engine sits stationary and is mostly ignored until the engine won't start and...259 replies | 23512 view(s)
-
08-12-2022, 12:40 PMI may just order a thicker (and slightly shorter) belt to get max potential out of it too. If I end up keeping it long term I would consider doing...259 replies | 23512 view(s)
-
08-12-2022, 11:26 AMYeah, still looking good. Your picture reminds me that I still need to install an anti-sway bar on the back of my buggy. (sigh). I guess I...24 replies | 1119 view(s)
-
08-12-2022, 11:06 AMYeah, now that motor is running in the "fun" zone. One of the reasons why I switched from my B&S Vanguard engine to the Predator 670 was for...259 replies | 23512 view(s)
-
08-12-2022, 04:23 AMEpic! [smilie=thumbs_up.g:[smilie=thumbs_up.g:[smilie=thumbs_up.g:[smilie=ext_hooray.:[smilie=ext_beer2.g:[smilie=non_banana1:[smilie=rockout3.gi:259 replies | 23512 view(s)
-
08-12-2022, 04:18 AMlol2608 replies | 611534 view(s)
-
08-11-2022, 10:43 PMPut carb back together and response seems the same. Turned slow speed screws out another 1/8 each for kicks. Painted the header. Test drive revealed...259 replies | 23512 view(s)
-
08-11-2022, 07:03 PMRear suspension coming together.... Fitted with a 52T sprocket. Skid shown here will clear up to 60T. Axle shafts are 18.75" 28-spline. ...24 replies | 1119 view(s)
-
08-11-2022, 06:41 PMThanks! Engine going in....24 replies | 1119 view(s)
-
08-11-2022, 02:48 PMThat’s how I understood the jetting also. Good to know on the fuel pump and that the cutout switch is easily rectifiable. I may add another throttle...259 replies | 23512 view(s)
-
08-11-2022, 02:37 PMThe different-sized jets were due to the exhaust pipe. One cylinder had a much longer distance through the muffler to exhaust, so the intake/exhaust...259 replies | 23512 view(s)
-
08-11-2022, 01:58 PMHave to throw in a little theoretical scientific-ness sometimes right? :p Hoping to get a test run in later today. Maybe I should do a timed 60...259 replies | 23512 view(s)
-
08-11-2022, 10:34 AMHow are those wind chimes going K ???2608 replies | 611534 view(s)
-
08-11-2022, 01:00 AMYour using Pythagoras now!259 replies | 23512 view(s)
-
08-11-2022, 12:18 AMDrilled the stock main jets from .0395 (.040 for ease of numbers) to .042; just over a 7 percent increase from stock. The 108 main jet measured...259 replies | 23512 view(s)
-
08-10-2022, 06:47 PMThanks Darwin! I hammered on it yesterday, and it seems cooler now with the belt being tightened. The next belt I get will probably be around half an...259 replies | 23512 view(s)
-
08-10-2022, 01:04 PMThe Dayco part number on your belt, HP3004, is a 1-3/16 belt. Since it's a little worn, it probably measures as a 1-1/8 belt. The center-to-center...259 replies | 23512 view(s)
-
08-09-2022, 07:40 PMDone (minus paint). Sounds OK with the baffles on, and very nice with them off.259 replies | 23512 view(s)
-
08-09-2022, 03:44 PMI don't know if Neil at ATV Racing in Phoenix can help but he may have info. (623) 516-86402 replies | 316 view(s)
-
08-09-2022, 01:10 AMHeader so far. I formed the collector by hand, literally as I dont have an anvil here at the moment.259 replies | 23512 view(s)
-
08-09-2022, 01:08 AM39mph is fast enough to get around. Few tweaks and there is more to be had to. Well done! :)259 replies | 23512 view(s)
-
08-08-2022, 09:33 PMWe’re up to 39mph and a much better takeoff. Won’t burn tires on pavement, but it should leave a mini-roost on dirt. Good enough for now until...259 replies | 23512 view(s)
-
08-08-2022, 03:40 PMI do need new front tires as these I picked up for $20 used, and they were a pain to put on. Im probably just going to cut the old arms off and...259 replies | 23512 view(s)
-
08-08-2022, 12:50 PMMan, that looks really nice. It will be a shame to get it all dirty when it's finished. :D24 replies | 1119 view(s)
-
08-08-2022, 12:48 PMThe Ridge Runner uses parts from a Polaris Sportsman ATV, if I remember correctly. I would bet that the sprockets from a Polaris would match yours.2 replies | 316 view(s)
