Activity Stream
-
Older Activity
-
Today, 04:49 PMThere was one corner in particular where Kenny was testing Justin on the inside. Barcia railed the outside, then came across the track to launch the...831 replies | 78805 view(s) -
Today, 04:45 PMSpent the better part of the day getting the wire harness closer to finish. Tidied up each wire, ran each appropriately, added in a few components...2340 replies | 402442 view(s)
-
Today, 04:41 PMNever heard of them? I recently became aware of them through the extreme enduro and trials.831 replies | 78805 view(s)
-
Today, 01:47 PMThis post didn't mean much when you posted it..lol831 replies | 78805 view(s)
-
Today, 12:28 PMHe was supervising I’ve considered building a double. But hadn’t thought of a table top. Table top would be the safer bet tho. Sent from my...7 replies | 664 view(s)
-
Yesterday, 11:34 PMcareful not to hit the dog there, you should build a tabletop jump so you have a landing ramp too7 replies | 664 view(s)
-
Yesterday, 04:06 PMRegarding the injuries, all I can say is . . . ouch!!! :( I think I sprained my thumb once. Other than that, I'm fit as a fiddle, which is a...2340 replies | 402442 view(s)
-
Yesterday, 03:32 PMGetting the peacock app on my firetv took about an hour though. I had to side load it through the downloader app, luckily there is a youtube how to...831 replies | 78805 view(s)
-
Yesterday, 03:28 PMI just realized I have free Peacock Premium with my X-Infinity internet! Yup, that means I can watch...831 replies | 78805 view(s)
-
Yesterday, 01:20 PMTry to keep it that way. I've seen my father go through major back surgery and it changed me somewhat. Otherwise, as always......Love your work. :)2340 replies | 402442 view(s)
-
Yesterday, 12:47 PMFortunately I have no pain in my left shoulder and minimal in my right. I have tears in three of the four tendons (along the grain, not against it...2340 replies | 402442 view(s)
-
Yesterday, 12:26 PMCompletely agree on the talent pool in both classes. I’ve read quite a few comments on the commentators volume being hard to hear at times and...831 replies | 78805 view(s)
-
Yesterday, 10:02 AMI thought both classes were good racing. Seems like there will be a lot of guys capable of winning this year. Was I the only one that couldn't...831 replies | 78805 view(s)
-
Yesterday, 04:31 AMThese both look like they hurt. Edit. Not that you will listen but your neck is more of a worry. C7/T1 looks compressed and calcified. Might...2340 replies | 402442 view(s)
-
Yesterday, 03:12 AMI was thinking the same.831 replies | 78805 view(s)
-
Yesterday, 01:31 AMAgreed. Was some good stuff.831 replies | 78805 view(s)
-
01-17-2021, 03:15 PMNot great, but not bad. Zack looked like the only rider making any progress. Cool for the dude that won.831 replies | 78805 view(s)
-
01-17-2021, 03:01 PMSpent most of yesterday afternoon tidying and routing wires, getting the loom cleaned up. I’d mess with a section, attach the positive battery...2340 replies | 402442 view(s)
-
01-17-2021, 02:34 PMLOL! You sound like the chiropractor that took the x-rays. ”I’ve seen some messed up shoulders but never anything like either one of yours. You...2340 replies | 402442 view(s)
-
01-17-2021, 02:29 PMGot it recorded... Heard a couple of spoilers for heat races. Hopefully Robyn naps this afternoon (usual Sunday practice) and I get TV time.831 replies | 78805 view(s)
-
01-17-2021, 01:42 PMRoczen figured lets not try the GasGas with BamBam onboard!831 replies | 78805 view(s)
-
01-17-2021, 09:06 AMI have no words.2340 replies | 402442 view(s)
-
01-17-2021, 03:36 AMGot the dash panel cut out and mounted up to the framework. Installed the voltmeter and switch panel as well. Currently more switches than I think I...107 replies | 13245 view(s)
-
01-17-2021, 02:05 AMWe got a little too rowdy with the AR51 at my friends farm. Unfortunately we didn't get it on camera though. I bombed a huge jump and bent a tie rod...7 replies | 664 view(s)
-
01-16-2021, 05:07 PMGot the exhaust system buttoned up yesterday. Realized that I hadn't installed the header gasket so I had to dig around on the table and locate it....2340 replies | 402442 view(s)
-
01-16-2021, 02:58 PMLooked a little dirty, how much gas are you using? Argon co2 mix?21 replies | 528 view(s)
-
01-16-2021, 02:44 PMK-Fab --- Thank you!! JMPerformance - I have edited and spaced some of my comments above to give you a better perspective on what to look for......3 replies | 89 view(s)
-
01-16-2021, 02:30 PMSeems to be the way of life for me starting at 5 with a concussion from spinning off a stool in a hamburger joint and stopping the concrete floor...2340 replies | 402442 view(s)
-
01-16-2021, 02:10 PMListen to this man’s advice. He’s by far the most knowledgeable about welding on this forum. The only other person I know on his level is not on...3 replies | 89 view(s)
-
01-16-2021, 01:23 PMThose welders perform fairly well just be sure a check/understand the limitations on 120v and 240v. Many of them have a far reduced output on 120V...3 replies | 89 view(s)
