Activity Stream
-
Older Activity
-
Yesterday, 05:07 PMGot the exhaust system buttoned up yesterday. Realized that I hadn't installed the header gasket so I had to dig around on the table and locate it....2332 replies | 401566 view(s)
-
Yesterday, 02:58 PMLooked a little dirty, how much gas are you using? Argon co2 mix?21 replies | 472 view(s) -
Yesterday, 02:44 PMK-Fab --- Thank you!! JMPerformance - I have edited and spaced some of my comments above to give you a better perspective on what to look for......3 replies | 52 view(s)
-
Yesterday, 02:30 PMSeems to be the way of life for me starting at 5 with a concussion from spinning off a stool in a hamburger joint and stopping the concrete floor...2332 replies | 401566 view(s)
-
Yesterday, 02:10 PMListen to this man’s advice. He’s by far the most knowledgeable about welding on this forum. The only other person I know on his level is not on...3 replies | 52 view(s)
-
Yesterday, 01:23 PMThose welders perform fairly well just be sure a check/understand the limitations on 120v and 240v. Many of them have a far reduced output on 120V...3 replies | 52 view(s)
-
Yesterday, 01:13 PMSo a couple of things. 1. Yes you need to use the same contact tip size, if not the current is not being passed into the wire as it should be ...21 replies | 472 view(s)
-
Yesterday, 12:45 PMYou all seem to chase pain and injury like me and the fridge. I'm board I wonder what's in here to eat? Other than that good progress and like...2332 replies | 401566 view(s)
-
Yesterday, 08:51 AMThank you!819 replies | 78363 view(s)
-
Yesterday, 01:47 AM*Same-day delay ^ Taped coverage #All televised coverage streams on NBCSports.com and the NBC Sports App Date Event Coverage# Time (ET)819 replies | 78363 view(s)
-
Yesterday, 12:37 AMHas anyone used the Titanium MiG 170? would it be good for industrial use? Here is the the specs: MIG 170 Professional Welder with 120/240 Volt...21 replies | 472 view(s)
-
Yesterday, 12:11 AMHas anyone used the Titanium MiG 170? would it be good for industrial use? Here is the the specs: MIG 170 Professional Welder with 120/240 Volt...3 replies | 52 view(s)
-
01-15-2021, 07:47 PMI am using 0.6 solid wire from Lincoln electric. The highest my welder runs is 120 amps, that is what I was running. could the contact tip be an...21 replies | 472 view(s)
-
01-15-2021, 02:31 PMI replied to your other post....3 replies | 59 view(s)
-
01-15-2021, 01:11 PMkustomfab2003 replied to a thread Is suspension ok mounted like this? in Suspension - Wheels & TiresHere are some pictures of mine as I was setting it up, hopefully these help.9 replies | 176 view(s)
-
01-15-2021, 01:07 PMMore info JM. And or pics!228 replies | 100460 view(s)
-
01-15-2021, 12:58 PMWhat sized wire did you go with? What gas also? Voltage will probably need to be 18-20V for .035 wire and wire feed speed anywhere from 175-245...21 replies | 472 view(s)
-
01-15-2021, 12:49 PMI did reverse the polarity after switching it to gas. The welder is all hooked up correctly to run the gas. I’m just having very bad issues with...21 replies | 472 view(s)
-
01-15-2021, 12:24 PMI am originally from Temecula, I know Glamis all too well!!! Thanks for looking out though. This was my first beam car I built back in 2009-2010...139 replies | 16230 view(s)
-
01-15-2021, 12:20 PMDid you change the polarity once you hooked up the gas connections? Solid wire runs DC +, you will need to change the leads so that the MIG gun is...21 replies | 472 view(s)
-
01-15-2021, 10:56 AMSorry, if the bead is forming on top of the metal and not bonding to it then you either need smaller wire, thinner metal, or more power. What welder...228 replies | 100460 view(s)
-
01-15-2021, 10:22 AMWelder is at its max voltage voltage settings228 replies | 100460 view(s)
-
01-15-2021, 09:48 AMIf you're using the same gauge solid core wire then you need more power...turn up the heat.228 replies | 100460 view(s)
-
01-15-2021, 05:36 AMI just wrapped up a sled conversion on Rennie Awana Gen 3 natures car. I was able to get a 5 gallon tank under the engine and behind the seat. Engine...79 replies | 16204 view(s)
-
01-15-2021, 01:32 AMI already did that. Everything is set up the way it should be. I’m just not getting good fusion at all3 replies | 59 view(s)
-
01-15-2021, 01:29 AMFlux core is usually done with reverse polarity. Try swapping it and see if it gets better.3 replies | 59 view(s)
-
01-15-2021, 01:25 AMI'm going to have to start up crashing lessons to show you guys how to do it with style.2332 replies | 401566 view(s)
-
01-15-2021, 01:14 AMTonight I tried hooking up the gas to my welder for the first time. I am having issues with the bead of the weld staying on top of the metal instead...228 replies | 100460 view(s)
-
01-15-2021, 01:13 AMTonight I tried hooking up the gas to my welder for the first time. I am having issues with the bead of the weld staying on top of the metal instead...3 replies | 59 view(s)
-
01-15-2021, 01:10 AMTonight I tried hooking up the gas to my welder for the first time. I am having issues with the bead of the weld staying on top of the metal instead...21 replies | 472 view(s)
