Activity Stream
-
Older Activity
-
Today, 04:06 PMRegarding the injuries, all I can say is . . . ouch!!! :( I think I sprained my thumb once. Other than that, I'm fit as a fiddle, which is a...2339 replies | 402164 view(s)
-
Today, 03:32 PMGetting the peacock app on my firetv took about an hour though. I had to side load it through the downloader app, luckily there is a youtube how to...828 replies | 78675 view(s)
-
Today, 03:28 PMI just realized I have free Peacock Premium with my X-Infinity internet! Yup, that means I can watch...828 replies | 78675 view(s)
-
Today, 01:20 PMTry to keep it that way. I've seen my father go through major back surgery and it changed me somewhat. Otherwise, as always......Love your work. :)2339 replies | 402164 view(s)
-
Today, 12:47 PMFortunately I have no pain in my left shoulder and minimal in my right. I have tears in three of the four tendons (along the grain, not against it...2339 replies | 402164 view(s)
-
Today, 12:26 PMCompletely agree on the talent pool in both classes. I’ve read quite a few comments on the commentators volume being hard to hear at times and...828 replies | 78675 view(s)
-
Today, 10:02 AMI thought both classes were good racing. Seems like there will be a lot of guys capable of winning this year. Was I the only one that couldn't...828 replies | 78675 view(s)
-
Today, 04:31 AMThese both look like they hurt. Edit. Not that you will listen but your neck is more of a worry. C7/T1 looks compressed and calcified. Might...2339 replies | 402164 view(s)
-
Today, 03:12 AMI was thinking the same.828 replies | 78675 view(s)
-
Today, 01:31 AMAgreed. Was some good stuff.828 replies | 78675 view(s)
-
Yesterday, 03:15 PMNot great, but not bad. Zack looked like the only rider making any progress. Cool for the dude that won.828 replies | 78675 view(s)
-
Yesterday, 03:01 PMSpent most of yesterday afternoon tidying and routing wires, getting the loom cleaned up. I’d mess with a section, attach the positive battery...2339 replies | 402164 view(s)
-
Yesterday, 02:34 PMLOL! You sound like the chiropractor that took the x-rays. ”I’ve seen some messed up shoulders but never anything like either one of yours. You...2339 replies | 402164 view(s)
-
Yesterday, 02:29 PMGot it recorded... Heard a couple of spoilers for heat races. Hopefully Robyn naps this afternoon (usual Sunday practice) and I get TV time.828 replies | 78675 view(s)
-
Yesterday, 01:42 PMRoczen figured lets not try the GasGas with BamBam onboard!828 replies | 78675 view(s)
-
Yesterday, 09:06 AMI have no words.2339 replies | 402164 view(s)
-
Yesterday, 03:36 AMGot the dash panel cut out and mounted up to the framework. Installed the voltmeter and switch panel as well. Currently more switches than I think I...107 replies | 13219 view(s)
-
Yesterday, 02:05 AMWe got a little too rowdy with the AR51 at my friends farm. Unfortunately we didn't get it on camera though. I bombed a huge jump and bent a tie rod...5 replies | 632 view(s)
-
01-16-2021, 05:07 PMGot the exhaust system buttoned up yesterday. Realized that I hadn't installed the header gasket so I had to dig around on the table and locate it....2339 replies | 402164 view(s)
-
01-16-2021, 02:58 PMLooked a little dirty, how much gas are you using? Argon co2 mix?21 replies | 518 view(s)
-
01-16-2021, 02:44 PMK-Fab --- Thank you!! JMPerformance - I have edited and spaced some of my comments above to give you a better perspective on what to look for......3 replies | 73 view(s)
-
01-16-2021, 02:30 PMSeems to be the way of life for me starting at 5 with a concussion from spinning off a stool in a hamburger joint and stopping the concrete floor...2339 replies | 402164 view(s)
-
01-16-2021, 02:10 PMListen to this man’s advice. He’s by far the most knowledgeable about welding on this forum. The only other person I know on his level is not on...3 replies | 73 view(s)
-
01-16-2021, 01:23 PMThose welders perform fairly well just be sure a check/understand the limitations on 120v and 240v. Many of them have a far reduced output on 120V...3 replies | 73 view(s)
-
01-16-2021, 01:13 PMSo a couple of things. 1. Yes you need to use the same contact tip size, if not the current is not being passed into the wire as it should be ...21 replies | 518 view(s)
-
01-16-2021, 12:45 PMYou all seem to chase pain and injury like me and the fridge. I'm board I wonder what's in here to eat? Other than that good progress and like...2339 replies | 402164 view(s)
-
01-16-2021, 08:51 AMThank you!828 replies | 78675 view(s)
-
01-16-2021, 01:47 AM*Same-day delay ^ Taped coverage #All televised coverage streams on NBCSports.com and the NBC Sports App Date Event Coverage# Time (ET)828 replies | 78675 view(s)
-
01-16-2021, 12:37 AMHas anyone used the Titanium MiG 170? would it be good for industrial use? Here is the the specs: MIG 170 Professional Welder with 120/240 Volt...21 replies | 518 view(s)
-
01-16-2021, 12:11 AMHas anyone used the Titanium MiG 170? would it be good for industrial use? Here is the the specs: MIG 170 Professional Welder with 120/240 Volt...3 replies | 73 view(s)